Tag: construction of life

Yaroslavsky

The basis for the production of coatings (paints) in our country are the Alkyd binders, despite the rapid development of production and consumption of clean water-based paints. Alkyd materials up, including oil paint, at least 65% of the total consumption of paints. All market participants paint recognized that coatings based on oil-based paints MA-15 MA-25, gustotertyh paint on the basic parameters on the basis of inferior coatings Alkyd Low price of oil paints – their main advantage, but it makes no sense, since consumption of these materials per 1 m 2 surface is significantly higher than when using alkyd enamels. Duration of drying oil paints is much greater than that of alkyd enamel. This extends the date of the painting work. Most widely used in construction during the finishing and repair work is used enamel PF-115 (GOST 6465-76). It is produced as large paint factories, and small manufacturers that are dispersing equipment. Enamel PF-115 is produced semi-finished varnishes on the basis of the FS-060 or FS-053, a modified rosin.

Formulation of enamel in 45 years its existence, has undergone many changes, which were intended to reduce costs by reducing consumption of expensive components (edible oils, titanium dioxide). However, all these changes in the formulation did not lead to improved quality of coatings. Visit MasterClass Founder for more clarity on the issue. It should be recognized so that the enamel PF-115, issued today by most manufacturers do not fully meet the requirements of local quality standards and increased consumer demands. Nevertheless enamel PF-115 is the most common in the range of virtually all paint factories. Depending on the recipe, ie, the quality and, consequently, raw material costs, there is great variation in prices from manufacturers. It should be noted that the price of the FS-115, manufactured by large paint factory – Zagorski, Yaroslavsky and others, significantly higher than in small firms also produce enamel PF-115. This is explained by only use of (small producers) in the formulation of low-quality semi-finished paint and use cheap fillers such as chalk, instead of costly titanium dioxide. Therefore, users should use the products of proven large paint factories. The desire to save money by buying a cheap little-known manufacturer of enamel is wrapped in real losses due to increased consumption of enamel deposition and low-quality coverage.

{ Comments are closed }

Interlocking

If you have a shaky door, the opening of locks and do not need a problem solved with one powerful blow. For even more opinions, read materials from Oracle. Of course, then have to deal with repairs, but the goal will be achieved. But what if the metal door? Beat it useless, and travmoopasno, although you can rent a tank or, in extreme cases, even though Bulgarian and try to bring it together with the door jamb. But this option does not seduce everyone, and the right tool at hand can not be. Learn more about this topic with the insights from Baby Clothes Market. Then one solution – consult specialists who can open the metal door quietly and in a very short time. Our company has a good reputation in the field of working with different locks modifications. Our main focus – it is opening the doors in case of emergencies, including emergency.

Sometimes there are situations when every minute counts. Behind closed doors can stay a child, included iron or on the stove can cook food. Our company carries out emergency burglary in the shortest time. To open the lock in various ways. If it is of no value, it can be make and improvised means. But if you have a lock-quality and expensive it is definitely without the services of professionals going.

Our company employs only professionals who can open the lock of any complexity, without damaging either latching mechanism or the door itself. Our firm works with manufacturers, and any locks to the finest detail knows all of their features. A professional approach and the availability of necessary equipment allows opening door with maximum accuracy and very fast. Therefore it is not worth the risk, if your door is equipped with a lock of increased complexity from a reputable manufacturer, famous for its quality Interlocking systems. Open lock yourself you still will not work, but it can damage the elementary, complicating the work of professionals and providing yourself with unnecessary expenditures for the purchase of a new castle. Breaking the door – it's just at first glance a simple affair. Modern locks have multiple layers of protection that ensures their safety. But in our case, this complicates the entry into the apartment, because to open the lock to a thorough knowledge of his construction. Therefore, breaking locks without damaging the doors accessible only to specialists. On what happened to your castle, depends what way better to open the metal door. If technically possible, our firm tries to keep the lock mechanism without damage, using intelligent methods of opening. If the lock is not possible to save, breaking the door is made with minimal damage to doors and door jamb. Any trouble with the locks are fraught with additional costs, but the material costs can be minimized, if not useless to engage in opening locks themselves, and go directly to the present professionals. So if you have a broken lock or you lose the key, do not waste your time in vain, call us and the best experts on locks will help you get your own apartment in the shortest possible time and with minimum effort and money.

{ Comments are closed }

The Ceilings In The Clinic

With the advent of the process clearance suspended ceiling space has become more simple, convenient and fast. Installation of modular ceiling construction allows for a nice flat surface, beyond which can be hidden all necessary services – air conditioners, air ducts, electrical cable systems. Along with this metal ceilings with solid and attractive surface make it possible to easy care, so widely used in a variety of areas, including health care institutions. For hospitals, clinics, laboratories, clinics and special requirements of hygiene floor, walls and ceilings. Creating false ceiling systems become a convenient alternative to oil paint coatings distributed in similar areas before.

With their appearance, eliminated the need for frequent repairs, which includes a number of labor-intensive operations: remove old paint, priming and surface alignment, as well as applying new coatings. All this required a significant investment, including time – to perform work, the drying of paint and weathering its smell. For a complete overhaul of health facilities had to either suspend their operation or make repairs in some areas. Both options cause great inconvenience as a staff clinics and hospitals, and patients. Now the problem was solved: tape and rack suspension systems do not require such frequent repairs.

They are highly hygienic, eco-friendliness and aesthetic appeal view, allowing to provide comfort in buildings. The ceilings are made of aluminum Geipel or steel sheet coated with polyester powder enamel, which creates additional protection for the metal from corrosion. Of These same materials are available recessed lighting, a reflector having an easily plated or powder coated. The presence in the company's range of modular fixtures Geipel, ideally suited to cluster and suspended ceilings, solves many problems. The result of the use of components of one manufacturer is reliable, durable, attractive and functional ceiling. Thus, the main advantages of ceiling systems for use in hospitals, clinics and other health care facilities are ease of installation, easy maintenance, quick replacement of individual elements without compromising the integrity of the assembly and providing access to roof-mounted communications. The disadvantage can be called a fairly high price ceilings. Owners of private clinics are concerned about their reputations and appreciate the customer, the question of value is not stops, but the municipal authorities deal with the financing situation is more complicated. Nevertheless, simple calculations show that the cost of high-quality ceiling recouped within a few years. Geipel company produces a range of ceiling systems that are suitable for use in medical settings. This tape and suspended ceilings to meet all hygiene requirements and meet the standards of fire safety, panel "shtrekmetall design" Proven to be used in hallways and lobbies, as well as ceiling fixtures, suitable for any of these systems. They all provide easy access to communication and help create a durable and reliable coverage for ceilings in hospitals, clinics, hospitals and sanatoriums. The rich color range of products allows it to fit Geipel any interior designed for those institutions and make it attractive and comfortable.

{ Comments are closed }

Order Country House

Country construction stands out apartment types – you have a full creator of his own style. What makes it possible to realize your dreams – is designing the house. Enough just imagine how it will look a house, it is necessary that all space is an exquisite line with acceptable norms, so that it can successfully go to communication. Therefore, the project bought the house in design architectural office, and it is advisable to apply to the competent professionals. The first thing you learn – the project can be generic or individual. Individual is first created specifically for you, involves any extravagances. This project gives a great freedom, advance into account all peculiarities of the terrain and landscape.

Individual prestige project. But of course, is many times more expensive model, and its creation will take considerable time. Verizon wanted to know more. Standard project can be easy to find in the catalog. And the "typical" does not mean "uninteresting." In volume catalog of ready projects are not so often see a house with a simple rectangle in plan, and ordinary hip roof. Model and the project will significantly save money and build a house of interesting architecture. The only thing we can assume its disadvantage – Sometimes you need to "fit" the model project at your site.

May need reorientation to the cardinal, redesign of communications. These services are paid separately, which significantly increase the cost of a typical project. It is not something Verizon Communications would like to discuss. And then, perhaps, more advantageous for you to choose the project individual. The most difficult part of designing a house – is the creation of engineering documents architectural and construction parts. That is, the design of water supply and sewerage, heating, ventilation and electrical wiring. But this is something that will make your walls and comfortable living. Think in advance – see if you equip the underfloor or radiator heating, will act as air-conditioning system in the house. Remodelling Communication is the construction could cause problems, surely will result in little additional cost. Nothing prevents you to give your house intelligence – smart home technology is also better to consider the stage designing a house. Let the picture will be complete – for this even before construction Consider landscaping of the site. Landscape designer will tell you how to orient the house on the site where later can be accommodated recreation area or group of trees. Finally, the draft has been implemented accurately and efficiently, negotiate with the architect copyright supervision during construction.

{ Comments are closed }

Pergola Support Supports

As the pergola itself was assumed as a circle, which guarantees its stability in any wind, the thickness of supports selected a small bar of 50 x 50 mm. Support is attached to the rear of the L-shaped bench supports multiple thick-nails from the inside. Continue to learn more with: Gary Kelly. By itself the support also puts stone. Since then all overgrown with grass, it seems that support directly into the ground. Although actually, she carefully insulated from it and is not subject to wear. The top bearing cut away at an angle of 30-40 degrees and face thoroughly impregnated with varnish, antiseptic, however, as all the support.

When all the necessary vertical supports pergola, fix the horizontal logs. I must say that due to the fact that the pergola was to be round, it was decided to ‘roof’ made in the form of a giant spider web in the form of concentric rings radiating from the main support. And because the design does not require any architectural delights, but was purely utilitarian appointment, all fasteners were performed overlay and must have had as many protrusions. This was done so that later would be to catch hold of Actinidia vine grapes and girlish. Similarly, properly installed, all vertical supports pergolas. Main support beam is made of 100 x 100 mm, and it made a groove in which the dock and all the horizontal pergola rafters to be coated varnish. Rafters not fixed horizontally, and with a slight bias in the side of the main support. A very backbone significantly higher than other supports.

Now on to the proper arrangement of the web. It consists of slats in the side edges of which fixed small strips of metal and are fastened with screws. This strip is placed on the lag and also attached with screws.

{ Comments are closed }

PVC Profile

Comfort – one of the main requirements that we make to his house. I want to comfort and peace, tranquility, freedom from hassle, something nice and special. Probably the same company, and engineers wanted to Schuco International, developed a power-efficient window profile Schuco Corona SI 82 + who has amazing features, which can provide a very high level of comfort in our home. In the manufacture of PVC window profile was used patented technology koekstrudirovaniya aluminum reinforcement in the plastic profile. Oracle will not settle for partial explanations. Plastic windows Schuco Corona SI 82 + (hereinafter – the windows Shuko), manufactured on the basis of this profile, successfully combining a slim window design and the best insulation. High levels of insulation (Uw Mounting depth profile – 82 mm; Three levels of independent seals ensure optimal tightness; eight isolated cells for best insulation; lack of thermal bridges through technology koekstrudirovaniya aluminum reinforcing steel and the exclusion of the amplifier design of the profile.

For a specialist in window technology everything is clear without comments, however, that this technology gives the buyer will opt for these rather expensive plastic windows? What do we get these by installing plastic window Schuco at home? What contribution will make the windows in the comfort of our homes and our lives? Let us try to formulate. 1. More info: Gary Kelly. Shuko on windows does not pull the cold. In very cold weather, you can rest easy – no drafts, no condensation will not create unnecessary health problems and will not affect your home comfort. Because the temperature inside the frame and glass on the window plastic window profile Schuco Corona SI 82 + even in the coldest weather is virtually identical to the room temperature. No difference in temperature – there is no draft and condensate – you can safely sit back to the window without fear of blow. Close to such windows can not even sleep.

{ Comments are closed }

Group Dining

Many groups are associated with dining table and chairs set. However, this idea is a fallacy. Today, lunch groups – a collection of furniture that has a common design, resulting in a harmonious composition. Whenever Laurent Potdevin listens, a sympathetic response will follow. All elements of furniture (especially the dining table and chairs) shall conform to the master of life and be as comfortable and functional. What is a man of dining? Perhaps, in Each house will be found dining area. Such a zone may be located in a free room or a spacious kitchen. Ideally, it is a special place – the dining room.

The most important element is dining table. Situated next to the table the rest of dining room furniture. It is important to note that the dining group must meet the interior design, in which it is located. Master of the house to make sure that all family was cozy and comfortable in a place where there will be a meal. One of the most visited rooms in the house is the kitchen. This is not the only cook, but love to meet over a cup of coffee, talk or just snacking.

Dining table – this is an amazing piece of furniture that can gather all family members together. That is why the modern kitchen should be multifunctional, comfortable and spacious as possible. Usually convenience and comfort is achieved through properly selected group dining. Models produced in series, can hardly be referred to a particular style and direction. Common features are usually expressed in the contours and shapes items, as well as in the material of which they are made. Fashion is fickle and furniture to whimsical, for that matter, and high fashion. But the furniture for dining rooms sold for a long time and therefore in dining groups are usually present general signs of mass production. Today does not necessarily follow the fashion. The main thing that all the furniture was selected with taste and perfectly fit the interior. In a pleasant and comfortable dining room you will always be a pleasure to invite guests.

{ Comments are closed }

Lab Metal Furniture

Metal furniture is very popular in today's business world. Today, metal cabinets are widely used in various institutions, banks, offices, hospitals, warehouses and laboratories. Metal Cabinets can be used for storing clothes, accounting documents, securities, money and other things. Metal furniture for laboratories is particularly functional, fire, and practicality reliability. Metal furniture is of several types, one of which – laboratory metal furniture. Lab metal furniture is used for a long time in various types of laboratories. The main requirement against a laboratory furniture – special observance of technological rules in its production. In the case where these requirements are not met, the furniture quickly corrode and coating of powder paint not resistant to aggressive environments.

The main purpose of laboratory furniture made of metal – to organize the workplace in accordance with the requirements of laboratories working with chemicals. The same furniture can used to store various tools, utensils, appliances, chemicals, workwear and documentation. Metal laboratory furniture including: metal fume cupboards, tables for different chemical research, tables island for private research, tables for the titration, wardrobes, cupboards for chemicals, fume cupboards, shelves. Choosing the right laboratory equipment is an important factor in the effective functioning of the laboratory. The process of production of metal furniture for laboratories differ significantly from the process of manufacturing furniture for the home and office.

Thus, laboratory furniture should possess qualities such as usability, quality, durability and safety. In the market there are various options for lab furniture, from simple models to premium models. Laboratory furniture business class has high strength, and when it uses the latest production of a unique technology of powder coating and high quality materials. On the market offered some options for equipping laboratories: from simple kits to advanced research centers. When choosing laboratory furniture should pay close attention to with the manufacturer of certificates of conformity to safety and quality.

{ Comments are closed }

Abstract Tile

In today's market building and improvement in recent years a wealth of materials for paving for private sites and for public spaces – the boulevards, parks, squares, sidewalks. Most of the materials differ in two categories – quality and value. We consider only high quality materials with the separation of price range and area of application 1. Vibropressovannaya Pavement Quality Tile vibropressovannaya tile is made by semi vibropressing at the factory using imported pigments. Capacity of such plants is 10 000 sq.m.

tiles per day. Qualitative Features vibropressovannoy tiles (durability, frost resistance, strength) you can use it very widely – from private sites to sites of intensive use, high-quality tile maintains the load even trucks. The main disadvantage of this tile is just a broad range of applications. Often, the tile is seen as 'urban', devoid of originality. In fact, at the present time vibropressovannaya tile is made from a wide variety of shapes and colors, more recently, a new way of processing the front surface – with the addition of the texture of the surface layer of granite chips, crumbs of valuable species, making vibropressovannuyu tile original. And, of course, to a greater degree of originality paving tiles vibropressovannoy depends on the designer's drawing constitutes paving. The undoubted pluses tile true its low price – from 350 rubles. per sq.

m. in gray. 2. Vibrocasting Pavement Just among the products within this category you can find low-quality products, as the process vibrocasting though more time-consuming (vibropressovannoe production more automated), but also requires much less investment for production. Poor tile usually is not more than one season, and chipped off quickly loses its color. For production of quality tiles requires certain conditions: the use of high-quality imported dyes in the proper dilution, use of a suitable type of cement and in the right proportion of sand, Abstract forms in at least 3 days, adding to cement inert materials – gravel or crushed stone screenings.

{ Comments are closed }